Wolverine Soffit and Decorative Trim Bedienungsanleitung

Fit and FinishInstallation GuideFor Siding and Vinyl Carpentry™Soffit and Decorative Trim

J-channels and F-channels3/8" J-channel1/2" J-channel3/4" J-channel1" J-channel1-1/4" J-channelUniversal siding and soffit re

Replacing a Damaged RestorationShapes Panel (Option 2)Required tools: hammer, wood chisel and hacksaw or utilityknife.Use a wood chisel to remove the

Random Hand-Split ShakesOverviewThe installation of Random Hand-Split Shake is unique in thatthe lap joint is hidden in the ribs between the shake pat

Install the next panel to the left of the installed panel. Lap thispanel over the installed panel, positioning the right edge of thepanel to a vertica

Install the next panel to the left of the installed panel. Lap thispanel over the installed panel, positioning the right edge of thepanel to the verti

Installing Millennium®SidingMillennium siding, which features the NailTight™Flexible Hem,attaches tight to the wall and floats from PermaFlex™suspensi

Fastening Millennium siding is different from other vinyl siding in that it isOK to drive the fastener up tight against the flexible hem. ThePermaFlex

Non-Horizontal ApplicationsIf installing these panels at 45° or less, hand punch a nail slotin the vinyl or drill a clearance hole just above the lock

Installing TrueComfortTrueComfort™insulated siding will help even out wall surfaces.However, to minimize extremes in the peaks and valleys ofuneven wa

All other accessories should be fitted with foam shims andfillers. These shims will ensure that the accessories are on thesame plane as the panels.To

Trimming Curved OpeningsFlexible J-channel simplifies installations around curvedobjects such as half and full round windows. To install aroundthe top

Utility TrimUndersill TrimHelps secure trimmed siding panels under windows and eaves.Dual Undersill TrimSecures trimmed siding panels under windows an

Frieze BoardA frieze-board appearance can be created using the 3-1/2"lineals in combination with new construction window starter orJ-channel used

Materials needed: J-channel, starter strip, coil stock andsiding. When choosing a siding panel, remember that widerpanels install more quickly than na

Repeat until both sides of the sunburst are completed.NOTE: To install the final panels at the top of thesunburst, bow the panels slightly and slip th

Replacing a Damaged Siding PanelTo remove a damaged panel, insert the hook end of a zip toolinto the lock between the damaged panel and the panelabov

Repairing Buckled Siding at the JoistVinyl siding sometimes becomes buckled between the firstand second floors of a newly built siding installation du

Cleaning Vinyl SidingVinyl siding resists most common household stains, but it willbecome dirty like any product exposed to atmosphericconditions. In

Siding over AsbestosVinyl siding retrofit over asbestosThis is a recommendation from the Vinyl Siding Institute afterdiscussions with Federal EPA offi

Exercise every care to retain architectural details whereverpossible. Do not remove, cover or add details until you havethe building owner’s written a

Miscellaneous AccessoriesCrown MoldingUsed in conjunction with 5" lineals to create a custom molded window or door header. Can also be used with

3/8" H-bar1/2" H-barJoins soffit panels. Particularly useful on porch ceilings and hiproof applications.3-1/2" Double Channel Lineal5&q

Cornerposts Outside Cornerposts3/4" Outside Cornerpost – Woodgrain3/4" Outside Cornerpost – Matte1" Outside Cornerpost – WoodgrainFor u

Equipment and ToolsSheathingsIn new construction, apply sheathing first, then nailaccessories over it.In home improvement projects, you can apply shea

For nailing instructions, see page 24.Tools RequiredHammer Tin snips Tape measureSquare Chalk line Level Utility knife Hacksaw Shears Power circula

Special ToolsNail Slot PunchPunches elongated holes to allow nailing the cut edge of a panel. Also used to enlarge an existing hole to allowproper nai

SidingUse the illustrations and formulas below and enter totals onthe estimating form in this section. These formulas apply forboth horizontal and ver

Upper wall of gambrel houseDivide the upper wall of a gambrel house as shown in theillustration. Then use the following formulas:1/2 (B + C) x H = ___

1Important InformationWarranties These instructions describe and illustrate the stepsinvolved in installing Wolverine siding and trim. Their purpose i

MeasuringBefore ordering accessories, you also have to determine thewidth of the J-channel into which you will fit the vinyl siding.To do this, you m

20Wolverine Fit and Finish Installation GuideEstimating FormSiding Walls __________ sq feetGable ends __________ sq feetDormer sides __________ sq fee

Preparing Wall SurfacesNew ConstructionMake sure all studs are straight and true. Correct any bowedstuds.NOTE: Vinyl siding must be applied over a rig

Apply rigid sheathing to existing siding to provide a smooth surface. Nail securely to old siding. Nail evenly to bridge low spots.NOTE: Failure to es

Applying over stuccoWhen applying vinyl siding over stucco, you first have to besure you’re working on an even surface. To create thatsurface, you may

Nailing, Stapling and Other Fastening MethodsIf you want to ensure a quality vinyl siding installation, focusyour attention on nailing techniques. Unf

Other fastening techniques:Manual nailing is the most common way of fastening vinylsiding to a wall. That’s because it offers greater control,making i

Expansion and ContractionIt’s normal for vinyl building products to expand and contractwith temperature changes. To ensure a successful sidinginstalla

A water level, a long clear plastic tube 90% filled with water, isuseful in marking level points around the house and onopposite sides of openings suc

Installing Outside CornerpostsFlash the corners of the home by bending a 10" wide piece ofaluminum trim coil 90° so you have two 5" legs. Co

The Wolverine Master Craftsman Program is your opportunity toearn valuable rewards while maintaining a leg up on yourcompetition. These rewards are no

Option 2: Cut a 6" length of cornerpost and trim the nailflange, receiving channel, and sides until you have just a 90°bend of vinyl. Using PVC p

Extra Wide Corner Posts (Four-Piece Corner System)Extra-wide cornerposts give you a distinctive, easy-to-installmethod of finishing outside corners. E

Inside CornerpostsThere are three options for trimming inside corners: Standard3/4" inside cornerpost, single J-channel, and two J-channels.To f

Federal CornersTo create a federal-style corner, flash the corner withaluminum trim coil or other flashing materials. Hang a newconstruction starter

Inside Federal CornersFlash the corner with aluminum trim coil or other flashingmaterials.Position and secure the 5" lineals (or a 3-1/2" li

Trimming Bay Window CornersThere are several ways to trim the odd angles of bay windows.Here are two of them:1. Install bay window cornerpost.2. Insta

Decorative Trim Options around Windows and DoorsJ-channelSystem requires standard J-channel.• 1/2" J-channel• 3/4" J-channel• 1" J-chan

Window FlashingThe width of all flashings is determined by the type ofaccessory surrounding the window and where the finalcomplete course of siding st

Installing Window and Door TrimInstall J-channel along the top and sides of door casings andaround windows.NOTE: When installing J-channel around repl

Drip ClipThe Drip-Clip is an easy and effective way to create rain tabsfor lineals. To install Drip-Clips, miter lineals with a power miterbox/chop sa

SECTION 1 – Introduction ... 5SECTION 2 – Materials and ToolsSiding Terms ...

3-1/2" Snap-on Lineal Application aroundWindows and DoorsThis application works only on 1"-faced J-channel.The installation of J-channel for

Measure the side casing and add 7". Use a triangle to create a45˚ angle or measure 3-1/2" in from the edge of the part. Usesnips or a miter

Lineal Starter Application for Windows and Door SurroundsWhen securing window and corner starter strips, outsidecorner pieces (OSCP), inside corner pi

Lineal Application around WindowsMeasure the top of the opening and add 7" (3-1/2" extra foreach side) if the side lineals are also 3-1/2&qu

Measure the height of the window or door. Add 7" (for the 3-1/2" header and bottom lineal) and cut. NOTE: Add additional material if using 5

Measure the bottom of the opening and add 7" (3-1/2" extrafor each side) if the side lineals are also 3-1/2". Add 10" total ifusin

Blind MiterAn alternative to a standard blind miter offers support to thecorner without adding material. The measurements shown for the fold are for a

Corner BlocksCorner BlockInstall starter as previously described. Measure and cut theside lineals to the exact size of the window or door opening.Cut

5" Square Header with Endcaps over 3-1/2" Lineals Sides and BottomsAssemble 5" header and cap. The side 3-1/2" lineals shouldexten

Creating End Caps for 5" LinealsTo create the header, first cut a 7" piece of 5" lineal. Measureand trim as shown.The resulting piece

4Wolverine Fit and Finish Installation Guide

5" Angled Header with End Caps over 3-1/2" Lineals Sides and BottomsAssemble the 5" header and cap. The side 3-1/2" linealsshould

Crown Molding Treatment OptionsOption 1 (page 51)• Crown molding• (2) crown molding end caps• 3/4" pocket J-channel header and surroundOther opti

Crown Molding and Cap for 3/4" Pocket J-channelTo use crown molding with 3/4" pocket J-channels, measure the length of the completed J-chan

Crown Molding with Cap for 5" Header LinealCrown molding with 5" header and 3-1/2" surrounds.Determine the header length by measuring f

Insert a crown molding cap into the crown molding and tracethe shape. Trim as shown.Insert the header cap. Cut the crown molding cap in half. Apply ea

Installing J-channel as Gable End TrimInstall J-channel to receive siding at gable ends, as shown in illustration. To create a clean, professional loo

Using Lineals as Gable TrimYou can give gable end trim a more dramatic appearance byusing 3-1/2" or 5" lineals instead of J-channel.To inst

Cutting PanelsTo cut panels to size, follow these procedures:Cross cutsFor a precise cut, use a power circular saw equipped with asharp, fine-tooth p

Preparing Wall SurfacesThe key to successful vinyl siding application is properpreparation of the nailing surface. It is essential that you workover a

Installing remaining coursesTo ensure best appearance, position the laps to avoidunsightly joint patterns. The illustration at left shows a well-plan

IntroductionPlan your work, then work your plan.That’s the key to success with any project, and it’s doubly true when it comes to installing vinyl sid

Fitting over windows and doorsThe procedure for cutting panels for installation over windowsand doors is similar to that explained earlier.If necessar

STUDfinder Installation SystemThe STUDfinder™Installation System combines preciselyengineered nail slot locations with graphics to create a sidingpane

Installing trim at roof lineTo prevent water infiltration along the intersection of roof andwall, install flashing before installing J-channel. At po

Fitting under soffitWhen you reach the last course of siding, you will probablyhave to rip cut panels lengthwise to fit under soffit.NOTE: If necessar

CompletionAttaching objects to sidingAll external products (downspouts, shutters, and lights, for example) are attached to walls after you’ve applied

Shutter Installation(A)The ideal application (shown at the top) has a joint betweenthe two shutters where the shutters are secured to the home.In this

Preparing Wall SurfacesFor the most part, the wall preparation instructions given forhorizontal siding also apply to vertical siding. The keyrequireme

Installing CornerpostsInstall outside and inside cornerposts using dimensions andprocedures described earlier.NOTE: Unlike the preparation for horizon

If a wall requires more than one course of siding, you canproceed in one of three ways:Use two lengths of J-channel, back-to-back, at the jointbetween

Installing Window and Door TrimFollow the instructions described earlier under the section“Preparation for Horizontal Siding” beginning on page 21.Pla

6SECTION 2 – Materials and ToolsWolverine Fit and Finish Installation GuideSiding TermsNail FlangeCommon to most vinyl siding products (includes horiz

Installing Wall PanelsCut the first of the partial panels (if partial panels arenecessary). Mark the cut line by measuring from the nail hemedge. Rip

Installing Gable End PanelsWhen installing vertical siding on a gable end wall, you shouldtry to create a balanced appearance.There are two ways to do

Requirements for Proper Soffit VentilationProper attic ventilation is important for any home. The 2003International Building Code (IBC) Section 1203 V

Porch CeilingsThe procedures used to install a porch ceiling are in manyways similar to those used to install soffit. These proceduresvary slightly, d

Remodeling ProjectsCheck to be sure the existing ceiling can serve as a solidnailing base. If the existing ceiling is solid, remove all existingmoldin

SoffitYou can use solid vinyl panels or perforated vinyl panels forsoffit installations. Perforated panels provide ventilation, whichhelps to reduce h

Installing SoffitMeasure from the wall to the fascia board. Then subtract 1/2"to allow for expansion. Mark this dimension on a soffit paneland cr

Installation over Enclosed EavesIf the existing soffit is rotted or damaged, it’s best to remove it completely before installing vinyl soffit. Then us

InvisiVent SoffitInstallation over open eavesIn most situations, InvisiVent™Super Ventilated Soffit shouldbe installed like our standard soffit produc

FasciaThe wooden fascia board that encloses the front of an eavealso needs protection from the weather. To provide thisprotection, you can install vin

Starter Strips2-1/4" Vinyl Starter StripSecures the first course of siding to the home. For use with all Wolverine sidings except Restoration Sha

For installations that include soffitNail undersill trim in place along the top of the fascia board.Then nail F-channel along the bottom outside surfa

D9 Rough-Split Shakes InstallationImportantThis product is not designed for roof application. It is designedsolely for installation on vertical surfac

If the brighter cell is between the numbered temperature cells,position the panel between the corresponding temperatureindicator lines. Example: If th

Second courseCut 29" off of the right side of the D9 panel at indicator“B,” which is located above the nail slots, cutting straightthrough the pa

Finishing the top courseTo finish the top course of siding, attach cornice receiver tothe top of the wall under the eave or soffit. Trim the top pane

Restoration Shapes Half-RoundsInstallationImportantThis product is not designed for roof application. It is designedsolely for installation on vertica

First courseStrike a level line around the house and install RestorationShapes Starter (see illustration 1a). An alternative method ofstarting Half-Ro

Second courseRemove 13-1/4" of the left side measured from the upperpanel, cutting straight through the lower panel course. (Note the small mark

Installing under a window or openingInstall Restoration Shapes undersill trim. Cut the panel to fitunder the window. Drill a 3/16" hole in the ce

Half-Rounds in Gable EndsNOTE: The following instructions focus on a gableinstallation. They also are geared towards an enclosedgable, started with a

Corner Starter StripSecures 3-1/2" and 5" lineals and a corner insert to theoutside corner.New Construction Window and Door StarterButts up

Hanging the starter courseTo end up with a single “round” centered at the peak of thegable, you must properly locate the first starter panel.Begin by

If you require an odd number of courses (i.e. five full coursesplus starting course), subtract 8" from the distance from theplumb line to the lef

Installing Restoration Shapes Half-Rounds on Non-vertical WallsHalf-Rounds must never be used as a roofing material.However, they can be used on non-v

Starting Half-Roundsover Horizontal SidingCut away nail flange and discard.Hand punch nail slots in panel face and secure panel.Secure Half-Rounds Sta

Starting Half-Rounds with Lineals over Horizontal Sidinghalf-rounds panel is inserted into thepocket of the lineal, making sure toleave 1/4" for

Application of Half-Rounds under SoffitThe amount of trimming required of a Half-Rounds paneldetermines the accessory piece required to receive it. Se

Replacing a Damaged RestorationShapes Panel with the Repair Kit (Option 1)Included in kit: cam clips, washers and pop rivets.Required tools: hammer, u

Push up on the panel to unlock and then pull down to removethe damaged panel.Preparing the new panelCut off all top locking tabs.Flip panel over and c

From the back, insert a pop rivet into a nail slot above one ofthe locking tabs. Then place a cam clip and a washer over thepop rivet. Squeeze the pop

Using your Wonder Bar or roof snake bar, drive the nails in byplacing the bar on the nail head and hitting the bar with ahammer.While applying pressur